Framed images are great for decorating and adding a personal touch to your room. However, you can't use nails in some places because it may leave holes, the walls won't be drilled or nailed, or the frames will be rearranged on the wall frequently. To fix this, you can hang the picture frame using tacks, various adhesive products, and other clever solutions. There are several ways to choose from, and you can determine the best method according to your equipment and needs.
Step
Method 1 of 5: Using Frame Hanging Strips
Step 1. Remove the objects behind the frame
The self-adhesive frame hanger strip must be affixed to a flat surface. Therefore, remove all objects that are "bump" on the back of the frame. This includes screw nails, wires, keyhole fasteners or anything else that makes the back surface of the frame uneven.
Self-adhesive picture hanging strips (as well as adhesive hooks and nails) can be purchased at stationary stores, craft stores, hardware stores, and the internet
Step 2. Clean the surface
The self-adhesive frame hanger strip must adhere well so that you can wipe the frame and the wall where the strip will be attached using a clean cloth and isopropyl alcohol.
Let the surface dry before attaching the strip
Step 3. Glue the strips
For each set of strips, press the two sides together. Remove one layer of protection, one set at a time, and press the adhesive against the back of the frame. Hold for 30 seconds. Repeat until the required strips are attached.
- A set of strips can withstand loads up to 1.4 kg, and a frame measuring 20 x 28 cm. If you're only using a set of strips, position them in the top center of the frame.
- Two sets of strips can withstand loads up to 2.7 kg and a frame measuring 28 x 44 cm. Position a set of strips at the top two corners of the frame.
- Four sets of strips can withstand loads up to 5.5 kg and a frame measuring 46 x 61 cm. Position one set of strips at each corner of the top of the frame, position another set on each side of the frame, about 2/3 of the way from the top of the frame.
Step 4. Mount the frame on the wall
First, peel off the protective film on the outside of the strip to expose the strip's adhesive. Then, press the frame against the wall. Gently separate the strip on the frame from the strip on the wall by pulling and lifting the two bottom corners of the frame. Press the strip against the wall with your finger for 30 seconds.
Step 5. Wait an hour
This will allow the adhesive on the strip to dry and harden. When an hour has elapsed, place the frame back against the wall by straightening the strips.
Method 2 of 5: Using Adhesive Hooks and Nails
Step 1. Clean the wall
Like the strips for hanging pictures, adhesive hooks and nails also need a clean surface to stick to. Wipe the wall surface with a clean cloth and isopropyl alcohol, then wait for it to dry.
Adhesive hooks or nails have adhesive on the back so they can stick to the wall. After that, you can hang your picture frame there
Step 2. Prepare the adhesive
Remove the cover from the adhesive strip and attach it to a hook or nail.
Some self-adhesive hooks have adhesive on the back. If this is the type of hook you have, skip this step and move on to the next
Step 3. Attach hooks or adhesive nails to the wall
First, remove the cover layer from the back of the adhesive attached to the hook or nail. Press the hook or adhesive nail for 30 seconds where you want it on the wall.
Step 4. Wait for an hour for the adhesive to dry
When it's been an hour. Hang the frame as normal in the space provided.
- Make sure you know the weight of the frame before buying self-adhesive nails as these are usually only capable of withstanding a load of 2.3-3.5 kg while small hooks can only withstand a load of -1 kg.
- To be able to hang much heavier frames, use more than one hook or self-adhesive nail. Make sure the weight of the frame is evenly distributed by adjusting the position of the hooks/nails during installation.
Method 3 of 5: Using Push Latch
Step 1. Select the hook type
There are several brands of hooks that are designed to fit into drywall without hammers, nails, or other tools. Some of them are Hercules Hook, Super Hook, Monkey Hook, and Gorilla Hook. These hooks are made of different materials and are able to withstand various loads. However, you will need to make a small hole in the wall for each hook. According to each manufacturer:
- Hercules Hook is able to withstand loads up to 68 kg.
- Super Hook is able to withstand loads up to 36 kg.
- Monkey Hook is able to withstand loads up to 15.5 kg.
- Gorilla Hook is able to withstand loads up to 22.5 kg.
Step 2. Attach the latch
Push the tapered, long and curved (no twist) end of the hook into the drywall wall. Once most of the hooks are in the wall, position them so that the small outside hook is facing up (to allow the frame to hang). Reposition it by pressing the remaining hooks against the wall.
Step 3. Hang the frame
Most push hooks sell for four or more per pack. Use two hooks to hang the heavy frame. Measure the length of the frame and divide it into three parts. Attach one hook at the 1/3 point, and the second hook at the 2/3 point. For an even heavier frame, use three hooks, and divide the length of the frame into four sections. Install one hook at point, one right in the middle (2/4 point), and the last hook at point.
Method 4 of 5: Using Masking Tape or Reusable Adhesive
Step 1. Select the adhesive type
You can use double-sided tape to hang light pictures on the wall, but it's not designed for that purpose and the paint can peel off when the tape comes off. Reusable adhesive, also known as sticky tack or poster tack is designed to stick light pictures on walls. However, this material can clump over time and be difficult to clean.
- The adhesive or reusable tape is strong enough to hold a poster or picture without a frame, but is not designed to withstand a load of more than kg.
- Single-sided tape can be converted into double-sided tape. Take a strip of masking tape, make a circle with the adhesive side facing out, and glue the two ends of the tape together to seal the circle.
Step 2. Prepare the wall to be pasted
The adhesive works best on clean surfaces. Therefore, wipe the walls with a clean cloth and isopropyl alcohol. While waiting for the wall to dry, wipe the back of the poster or image with a clean, dry cloth.
Wash your hands before handling the reusable adhesive to prevent dirt and grease from transferring to the adhesive
Step 3. Prepare the image
Spread the image face down on a flat surface. Press a small ready-made adhesive ball or square of double-sided tape on each corner of the back of the image. If you are attaching a large image, use tape or tape along the back edge of the image.
Step 4. Mount the picture on the wall
After using the adhesive or tape, lift the picture and stick it on the wall. Position it so that it is perpendicular to the wall, and press it so that the tape or tape is firmly attached to the wall.
Method 5 of 5: Using Yarn
Step 1. Locate the frame fittings that are already on the wall
Look for hooks, screws, nails or knobs that are already attached to the wall and can hold up to a few pounds. Note that this method works best with borderless images/photos.
Look for an object on the wall that is out of reach and can be threaded together without disturbing anyone
Step 2. Tie the thread
Cut thread or wire that is long enough to connect the two wall fittings, and still have some left to tie to the fittings. You can pull it tight or let it loose a bit and fall off.
- Tight yarn will appear stiffer and more uniform, while loose yarn will appear more relaxed and artistic. Make a choice according to your aesthetic taste.
- Wire is more difficult to tie than yarn and gives an industrial look. In addition, the image can also be shifted to quickly rearrange its position. Because it is thin and strong, the wire cannot give the appearance of falling.
- Knitting yarn is easier to tie and can be dropped or pulled tight, but is stronger than regular yarn. Because they are thinner, regular yarn is not as strong as knitting yarn.
Step 3. Hang your image
Use clothespins or clips to attach the image to the thread. If your yarn is starting to fall off more than it should or the knots keep coming off, it may be that the drawing load is too big. Use knitting yarn or stronger wire, or tie a second yarn to a different hook for the second row of images.
To evenly distribute the weight and drawing, place the first image in the center of the thread using your naked eye or a measuring tape. Use the first image as the center point that divides the yarn in half, and divide the half of the yarn in half again, placing one image in each midpoint. Continue dividing in half and using the center point as the location of the image until everything is hanging on the wall
Tips
- Wall-mounted cork boards can be used to attach pictures.
- Tacks can be used to hang loose-fitting frames, posters, or very light frames with wire hangers, as long as you can drill a small hole in the wall.
- Loose style frames or frames can be displayed by leaning against bookshelves, furniture, or other objects, or placing them on standing frames.
