Broken glasses can be difficult and frustrating for you. In addition, glasses can not necessarily be repaired immediately. Whether your eyeglass lenses are scratched, a screw is loose, or the bridge is broken, you can fix it before you get a new one.
Step
Method 1 of 5: Repairing a Broken Glasses Bridge with Glue and Paper
Step 1. Use glue and paper to fix the glasses
You can use glue as a makeshift eyeglass bridge repair (the part that rests on the nose).
- Make sure the two pieces to be glued are clean. (Remove any glue from the previous experiment. If you used “super glue”, try removing it with a nail polish containing acetone while being careful because this product is hard on the frames).
- Prepare all equipment on the job site. Provide the following supplies: Super glue (Locktite, Krazy Glue, etc.), a piece of photo paper (glossy) or thick magazine paper that fits the eyeglass frame, sharp scissors.
- Cut the wrapping paper into thin strips that are about the size of your glasses.
- Glue the paper to the frame with glue, one strip at a time. Use short strips of paper as a splint along the broken bridge, or wrap it like a bandage.
- Wait for the glue in one area to dry before moving on to the next.
Method 2 of 5: Repairing a Broken Glasses Bridge with Stitches
Step 1. Prepare the ingredients
You'll need thread, a needle, a drill, sanding paper, a paint mixing stick, rubber bands, wax paper, alcohol swab or nail polish remover, and a craft knife.
Step 2. Clean and sand the broken part of the glasses
Use sandpaper to clean and smooth the damaged area to be glued. Wipe the area with rubbing alcohol or polish remover to prepare the surface of the glasses.
Step 3. Tie the two broken pieces together tightly
Cut the paint mixing stick and position it so that it bridges the two “temples” (the sides of the glasses). Cover the lens with wax paper to prevent scratching and wrap a rubber band around one end of the stick and secure it to the glasses. Do the same on the other end.
Carefully align the two halves of the glasses and make sure the rubber bands are firmly attached to the glasses. If the break isn't "smooth" and creates a gap, straighten the pieces of the glasses as much as possible to ensure a solid point of contact
Step 4. Glue it with glue
Coat the broken part with glue. Use just enough glue to glue the glasses bridge together but don't let it drip or run. When filling in the broken parts, try to have no empty spaces or gaps. Use a cotton swab to gently remove any residual glue; wipe before the glue has time to dry or stick. Set the glasses aside for at least an hour to allow the glue to dry completely.
Step 5. Make two holes with a drill
Choose a small drill bit that matches the thickness of the eyeglass frame. Take your craft knife, and make initial holes on either side of the newly repaired joint. Place the glasses on a soft cloth spread over the table and drill finely on both sides of the broken part. The holes made must be parallel to each other so that they can be used to wrap the thread over and over again at the core joint.
Step 6. Sew the rubber band
Use a 1-2 meter long needle and thread that matches the eyeglass frame to "sew" both sides of the fix so that it is even stronger. Pass the needle and thread through both holes as much as possible and try not to pull and press the newly repaired joint too hard. Stop when there is no more room. Fill the drilled holes with glue until all the threads are wet, and wipe off excess glue with a cotton swab. Trim the edges of the thread and let it sit for an hour to allow the glue to dry.
Step 7. Add the dressing
If you want to increase the power of your repair, try these additional steps. Do not trim the edges of the thread as suggested above. Instead, once the glue is dry, take the remaining thread to one side and wrap it around the bridge of the glasses from front to back. Make the dressing as neat as possible; a little bit of criss-cross is fine, but make sure your wrap isn't too thick. Leave the short end of the thread to cut later. Wet the thread with glue and let it dry for 10-15 minutes. Take the thread from the other side of the glasses and wrap it around the bridge of the glasses in the opposite direction (back to front). Moisten the bandage with glue and allow it to set for a few minutes before trimming the loose ends of the threads. Leave the glasses for 24 hours before they can be worn.
Method 3 of 5: Repairing a Broken Bridge with Heat and Pins
Step 1. Boil water until it boils
Fill the kettle with water and turn the heat to a “high” setting. Since you're using heat, this method of fixing glasses only works on plastic frames.
Step 2. Melt the plastic
Once the water boils, hold the broken rim of the glasses as close to the kettle as possible so the heat softens the rim of the glasses.
Step 3. Enter the pin
Push a small pin into one of the edges and press the other edge of the glasses against the pin. While the plastic is still hot, smooth the glued parts.
Never directly touch the plastic of the glasses with fire
Method 4 of 5: Replacing Missing Screws
Step 1. Use the eyeglass repair kit
Eyeglass repair kits can be purchased at pharmacies and contain all the supplies you need to repair glasses: screws, a small screwdriver, and sometimes a magnifying glass. Newer versions of the kit contain longer screws for easy gripping. Insert the screw into the hinge, tighten it, and “break” the bottom of the screw so that it is flush with the hinge.
If you're having trouble aligning the hinges at your temples and the front of your glasses, it's possible that the hinge mechanism inside your temples is being stuck. To fix this, use the end of the hook on a safety pin and thread it through the temple hinge hole and carefully pull it out. To prevent the hinge hole from moving, insert the second paper clip perpendicular to the “slit” created when you removed the clip from the hinge hole. Align the eyeglass front and temple holes, insert the screws and tighten them. When you're done, remove the paper clip from the slit and the hinge hole will slide back into place so that the glasses snap into place
Step 2. Try using a toothpick
When the screw loosens from the hinge that holds the front and temples of the glasses together, try using a toothpick for emergency repair. Align the temple hinge with the front hole and press the toothpick until it goes into the hole as far as it will go. Break or cut the remaining toothpick sticking out.
Step 3. Replace with wire
Unscrew the plastic sheet from the wire binding of the bread wrap. Align the hinge holes and thread the wire through them. Twist the wire until the front and temples of the glasses are securely in place. Cut the end of the wire sticking out so it doesn't scratch your face. You can also use safety pins (which are usually used for clothing price tags). Insert the pin through the hole so that the glasses are firmly attached.
Method 5 of 5: Removing or Filling Scratches on the Lens
Step 1. Use a special product for scratched lenses
Provide a lens patch product for your scratched lens. This product works by removing the anti-glare and scratch-resistant coating on the lens while keeping the original lens untouched. You should only use chemical lens sealants on plastic lenses, and never use them on glass lenses. Other specialty products can temporarily fill in scratches on the lens so they are less noticeable, but leave a glossy film mark on the lens.
Be careful not to clean and polish the lens until it changes the surface thickness. Any product or procedure that alters the surface of the eyeglass lens will interfere with the refraction and effectiveness of the lens
Step 2. Use a household cleaner
Abrasive cleaners, baking soda, and toothpaste can all be used to polish a scratched surface. Waxed products like Lemon Pledge and Carnauba will fill light scratches with wax. However, the wax will reduce visibility and will need to be reapplied every few days. You can also try using rubbing alcohol or diluted ammonia. After using one of these products, blot it with a soft cloth, ideally one specifically designed for cleaning glasses.
Step 3. Prevent the return of scratches on the lens
The lens is a delicate part and must be treated carefully to avoid scratching it.
- Use a glasses case. A strong, cushioned case will protect your glasses. It's a good idea to store your glasses in this box instead of in your pocket or put them directly in your bag.
- Clean eyeglass lenses. Clean eyeglass lenses daily with soapy water and frequently with a clean, soft microfiber cloth.
- Stay away from unfriendly products. Some products can damage the lens and should not be used. Don't use facial or kitchen paper towels to wipe your glasses and stay away from antibacterial soaps for cleaning lenses. Do not use hairspray, perfume, or nail polish remover, as these can scrape off the coating on the lens.
Tips
- Don't let the glue get on the lens from your fingers.
- In an emergency, the best method of repairing a broken eyeglass bridge is to apply tape to hold the two pieces of your glasses together. Choose a tape color that matches the color of your glasses or spice up the look of your glasses with decorative tape.
- If white residue appears on the frames of your glasses from coming into contact with acetone, try scrubbing them off with an oil-based lotion..
