Pushing is a method of starting a vehicle's engine by activating the transmission while pushing the vehicle forward. On a motorcycle, pushing is a very useful skill just in case the battery dies or the engine won't start. Read on for this article to learn how to start a motorcycle engine.
Step
Step 1. Check if there is anything else preventing the motorcycle engine from starting
Before pushing the motorcycle to start it, save time by checking for other problems that simply won't work by pushing it. For example, you only need 1 second to check if the fuel is still there, by looking at the fuel indicator. The following is a list of quick checks you can do before trying to push the motorcycle. If any of the conditions below are not present, this may be the reason why your motorcycle won't start:
- The fuel in the tank is still there.
- The ignition key is in the " on " position (usually applies to older motorcycles).
- The standard has been raised.
- Teeth are in neutral.
- The kill switch has been set to the "run" position.
Step 2. Change gears to 1st or 2nd gear
Starting the motorcycle by pushing must be done in low gear. On most motorcycles, gear 2 This is the most comfortable position for this purpose, although many also do it in 1st gear. While this is rare, some motorcycles are easier to start in 1st than 2nd gear.
Parked motorbikes are usually in a neutral position. This can be determined by pushing it forward. With a neutral position, the motorcycle can be moved forward without having to press the clutch. To shift the gear from neutral to 1 on a manual motorcycle, depress the clutch, then press the shift lever (which is in front of the footrest) down. To shift from 1st to 2nd, press the clutch and lift the shift lever up
Step 3. Depress the clutch and push the motorcycle
Most guides recommend pushing the motorcycle at a minimum speed of 8 km/h to start the engine. This requires a lot of space up front so you'll need to get rid of any obstructions before you start pushing. You may also want to have plenty of room left and right in case you lose control when the engine is running.
Pushing speed can be easily obtained if you run the motorcycle on a downhill road. If you come across a road like this, instead of running pushing the motorbike from the side, you can just ride it. Be careful when driving the motorbike on downhill roads, lest you lose control of the motorbike
Step 4. Release the clutch, then press the starter button
After reaching sufficient speed, release the clutch and press the starter button using a smooth motion as the motorcycle slides forward. Give the gas in the medium level. Immediately after the motorcycle engine starts, press the clutch again so that the motorcycle does not jump forward.
Step 5. Keep the engine running
After the motorcycle is successfully turned on, try not to let the engine die again. With the clutch still pressed, turn the motorcycle gas on a medium level so that the engine does not stop.
By continuously turning the gas on the motorcycle, you will also charge the battery (if the motorcycle will not start because the battery is dead)
Step 6. Ride your motorcycle
Once the engine is started successfully, chances are the motorcycle won't turn off again, unless you turn it off on purpose or the engine stalls. If the motorcycle battery runs out, you can drive around on the motorcycle or spin the gas to charge the battery so you don't have to push it again later.
Before turning off the motorcycle, first address the underlying problem that prevents the motorcycle from starting (or at least you are prepared to do so). A motorcycle that needs to be started by pushing may have a problem with the battery or fuel system, which should be addressed by a mechanic. For example, if the battery is running low, drive your motorcycle to the nearest repair shop to get a new battery before you turn off the engine
Tips
- Downhill trails are perfect for this purpose and don't require much effort. Motorcycles are not light vehicles.
- The higher the boost speed and the higher the gear you are in, the easier the motorcycle will start.
- The use of a higher gear will give the wheels a large mechanical advantage to start the engine (conversely, a lower gear will give the engine a large mechanical advantage to drive the rear wheels). The use of 2nd gear can make motorcycle tires skid on the road surface, especially if you are trying to start the high compression engine on a road full of gravel.
- If this method fails, and you do not have sufficient knowledge about motorcycle maintenance, take the motorcycle to a repair shop for repair.
Warning
- Don't do this on a busy street.
- Don't forget to wear a helmet.
