A bong, also known as a pipe with a water tube, can allow you to inhale large amounts of dense cigarette smoke. This will help you to reduce the number of cigarettes smoked and remove many carcinogens such as tar from your cigarettes. Great space on the ' bong' cool smoke. The smoke produced is cleaner, lighter and cooler than conventional smoking methods such as kretek cigarettes or with a pipe.
Step
Step 1. Look for bottles or cans of any type (2 liter/16 ounce sizes will work)
Step 2. Crumple or heat a paperclip with a lighter and make a hole measuring 1/8 inch (3mm) to 1/4 inch (6mm) or about 2 inch (5cm) from the bottom
This hole serves as a place for the cigarette to fit into the bong of the bowl and vaporizer (the smaller the hole around the vaporizer, the less tape or insulation you'll need. Doing this requires some skill!).
Step 3. Install the tube in the hole you made at the bottom
These cans can be made from metal pipes, empty pen tubes, or vaporizers purchased from a store or online. Make sure the tool is slightly angled or your tobacco will get wet.
Step 4. Make sure the bong is airtight
If it's not very airtight then the smoke will come out of the hole unnecessarily. To fix this, use chewing gum (which is the most effective covering material) or masking tape. To test the airtightness, place your hand on the seal and blow against the mouth of the bong. If air comes out it means the bong is not airtight. You can use a rubber seal to make it more airtight (see Tips).
Step 5. Attach the bowl to the end of the tube
If possible, choose a cheap glass bowl from your local cigar shop, which usually costs around Rp. 65,000.00. You can also grind a kretek cigarette with a paper roll and attach it to the end of the tube. Aluminum foil can be used but we don't recommend it. Please check to ensure that the bowl material is safe to smoke before use.
Step 6. Fill the bong with water until the tube in the bottle is about 1 inch (2.5 cm) filled
You can fill it more, but there will be less smoke in the bong chamber when you smoke it. Make sure you don't add too much water to wet the tobacco.
Step 7. Place the carb or 'cleaning hole' in the center of the bottle down, making sure it's not so low that water comes out when you suck it in
The hole seen in this image is in a high place so that it does not allow smoke to mix with the incoming air. This allows oxygen to enter the bong.
Step 8. Fill the bowl with your favorite cigarette product, close the cleaning hole with one finger, turn on the filled bowl while sucking it in slowly
Step 9. Smoke the Bong chamber, then open the cleaning hole and suck firmly
Exhale.
Step 10. Done
Tips
- If possible, use a metal or glass vaporizer. Both of these materials are safer because plastic vaporizers can produce toxins, especially if the bowl is metal because metal conducts heat.
- Once you get used to this method, try different bong configurations. Try with multiple spaces, for example a cooler filled with ice for a light effect.
- Do not use aluminum/tin foil; This paper is dangerous and bad for your health.
- Instead of using water, you can use fruit juice or cherry cola or something else.
- Personalize your bong! Stick a sticker or give a name to the bong.
- You can also use a vaporizer with a retractable system, which allows you to remove the vaporizer and let the air in. This method does not require a separate hole to be drilled again.
- To make the vaporizer and steam vent more airtight, use a rubber seal. These rubber seals can be found at your local hardware store. Make sure the vaporizer fits snugly against the rubber seal before purchasing it.
- You don't need to add water to it, you can try various fruit-flavored drinks or the like to add flavor.
- This method can be done using all types of plastic bottles, from 500 ml to 2 liters, and even more. Try all the bottles as much as possible, each bottle has a new sensation.
- Make sure to make a smooth hole, so you don't lose pressure. It will be a little difficult, but with practice, it will become easier. If the smoke hole is rough, simply add hot glue to cover the sides of the hole. Glue is better than using duct tape.
Warning
- Making your own bong may seem unethical. Cigarette shops near you may sell good glass bongs at affordable prices. When buying a bong, tell the seller that you are looking for a cigarette pipe with a water tube. This is important because the word bong itself is often associated with marijuana.
- If you melt the plastic and inhale it, not only will this be bad for you, but it will taste very bad and you will cough.
- Do not use PVC, copper, aluminum, or plastic on parts that will be exposed to heat. Do not smoke with tinfoil or glue with hot glue near the bowl, as the smoke you breathe in will be toxic and carcinogenic.
- Check local laws to see if your favorite cigarette product is illegal.
- Use bongs only inside your private home. Even if you only smoke tobacco or other legal products, law enforcement will try to harass you. If you need to smoke outside, consider a small bong that can be tucked into a car glove compartment or tossed in the trash if needed.
