Have you ever been irritated by the squeaking of a chair that won't stop? Squeaky chairs will irritate those around you. However, there is no need to rush to buy a new chair. Once the squeaky chair is thoroughly inspected, the problem can be easily resolved.
Step
Method 1 of 2: Lubricating Metal Parts
Step 1. Check nuts, bolts and screws
The first thing to do is turn the chair over and take a look at all the hardware. Use a screwdriver or wrench to tighten loose nuts, bolts, or screws. If you can, tighten the other parts as well. Over time, the screws and nuts will loosen, causing certain parts of the chair to rub against each other and squeak.
Step 2. Lubricate the seat mechanism
Apply lubricant to all nuts, screws, and bolts to help loosen joints. Spray the lubricant directly onto the seat mechanism and pat it dry with a cloth. You can also spray the lubricant onto a soft cotton cloth and rub the cloth over the problem area so you can control the direction the lubricant flows.
Moisture in air and air conditioners can cause rust. Regular lubrication will prevent the appearance and deposition of rust
Step 3. Remove the bolts and screws completely before applying lubricant
If your seat still squeaks after lubricating and tightening all the bolts and screws, remove them and lubricate them with light engine oil before reinstalling the bolts and screws.
Step 4. Have your friend sit on a chair while you lubricate the oil
So that you can easily find the squeaky area of the chair, have someone sit on it and turn it sideways. Heavy load assistance will make it easier for you to locate the source of the squeaking sound for more accurate oil application. Every time you apply oil, have your friend turn the chair to make sure the oil is applied in the right places.
Step 5. Fix the spring behind the seat
Your seat may only squeak when you lean back, which is usually caused by too much pressure where the ends of the springs rub against the ends of the housing. To fix this, spray grease on the seat pressure spring that is inside the swivel knob housing. You simply loosen the swivel knob for seat pressure and release the knob so you can spray grease into the housing.
Step 6. Move your chair back and forth to check the wheels
Office chairs usually have wheels on the bottom and move around a lot so it's only natural that the wheelbase will need some silicone spray over time. Flip the chair over and spray silicone on the wheels. After that, return the chair to its original position and roll the chair so that the silicone spreads over the entire wheel.
Step 7. Sit down slowly
If you drop into a chair, eventually the chair will squeak due to wear and tear. Therefore, in order to keep your chair calm, sit carefully so that the joints don't break too quickly.
Method 2 of 2: Repairing the Wooden Chair
Step 1. Check for loose legs, screws, or nails in the wooden chair
Check how loose your chair legs and backrest are by pulling and pushing back and forth to see how much the chair moves. The chair should not move.
Step 2. Turn over the chair to be repaired
You can turn the chair over at a table or other chair so that the problem area can be accessed more easily. It also prevents unwanted pressure on the legs or the back of the chair as you work.
Step 3. Glue the loose joints with glue
There are many strong wood glue products to buy that can stabilize loose leg joints. When you find the location of a loose joint, apply wood glue to the joint and allow it to dry completely before overturning the chair. Wipe off any excess glue with a damp cloth.
To make your wood glue thicker, try adding wood filler to the glue. A thicker mixture will stabilize the chair legs better
Step 4. Inflate the dowel (the small part that connects the two structures) with wood-swelling fluid
For chair legs that seem to need more than glue, remove the legs all over the chair and use wood-swelling fluid. When you pour wood-swelling fluid on the dowel, it will snap back into the chair
Step 5. Replace the nails or wooden joint stoppers
If the chair hardware seems loose or no longer in good condition, replace it with a new one. Even if you don't want to remove the existing hardware, you can strengthen it by adding nails or bracket hinges to make the seat more solid. When installing additional screws, make sure they are long enough to hold the wood together, but not so long that they go through the other side of the wood.