A popsocket is a device that can be attached to the back of a cell phone. With a popsocket, you can hold your phone more comfortably, especially when taking selfies. You can also use it to do other things, like store headphones and hold your phone up. The popsocket holder can be placed on a surface such as a car dashboard to hold the phone firmly, while the popsocket is attached to the phone.
Step
Method 1 of 3: Installing Popsocket
Step 1. Buy popsocket from online marketplace
You can choose from a variety of colors and designs. You can also design your own popsocket by uploading a unique image and ordering it.
To order popsockets, please look for shops that offer custom-made popsockets at the market place
Step 2. Decide on the point to mount the popsocket
Decide in advance where you will position it based on how the popsocket will be used. Place the popsocket on the back of the phone without opening the tape to see where it is. If you want to install two popsockets on the back of the phone, test them out and make sure they are aligned.
- For example, if you want to support the phone vertically, place the popsocket at the bottom of the phone.
- You can attach two popsockets to support a larger phone or hook up the speakerphone.
- Decide whether you want to attach the popsocket directly to the phone or to its case.
Step 3. Peel off the sticker on the adhesive surface
Once you are ready to install the popsocket, carefully peel off the sticker on the back. Gently tug on the sticker so it doesn't tear, starting at one corner and lifting carefully. Do not peel off the adhesive cover until you are ready to attach the popsocket to the phone.
Step 4. Paste the popsocket to the phone
Once the adhesive surface is exposed, press it against the point where the popsocket will be installed. Press firmly for 10-15 seconds to make sure the popsocket is completely attached to the phone.
Method 2 of 3: Repositioning Popsocket
Step 1. Compress the popsocket before opening it
Press the popsocket down to align it to the back of the phone. Popsocket will be easier to open in a compressed state like this. Do not try to open the popsocket while it is inflated as this may cause the popsocket to fall off the bottom.
Step 2. Gently peel off the popsocket from one corner
Pick a corner and peel it off slowly. Keep pulling in a circular direction to release the outer surface. Once all the circles are released, pull the popsocket to remove it.
Step 3. Use dental floss to remove the popsocket if it can't be pulled
If the adhesive is too strong to remove by hand, slip dental floss underneath to remove the popsocket. Tie the end of the floss to your index finger and position it on one edge of the popsocket. Slide the thread slowly but firmly between the popsocket and the phone to separate the adhesive.
Step 4. Rinse and dry the popsocket if the adhesive part is dirty
Make sure the adhesive part of the popsocket is clean so that it can be re-glued properly. Rinse gently under cold running water and let sit for 10 minutes to dry. Re-glue it to another surface in 15 minutes, or the adhesive will dry out.
Step 5. Glue the popsocket to the new surface
Choose a new place for the popsocket, either on the same phone or a different one. Press the popsocket firmly so that the adhesive sticks to the phone. Press and hold for 10-15 seconds to make sure the popsocket is firmly attached.
Method 3 of 3: Installing the Popsocket Holder
Step 1. Purchase a popsocket holder at the market place
This holder can be found in the accessories section of the phone. Popsocket mounts can be attached to surfaces such as a car dashboard or bedroom mirror.
- Purchase a popsocket mount at an online store or local cell phone accessory store.
- You can also purchase popsocket mounts that are designed to attach to a car air conditioner fan.
Step 2. Wipe the adhesive surface with rubbing alcohol
Make sure the popsocket holder has a clean surface to stick to for a good adhesion. Pour a few drops of alcohol on a cotton swab or use a paper towel with rubbing alcohol to wipe the area where the popsocket holder will be attached. The surface will dry after a few seconds.
Step 3. Peel off the adhesive cover on the back of the stand
Gently peel off the protective sheet covering the adhesive on the popsocket holder. Don't touch the adhesive! The 3M VHB pads are designed to adhere firmly and will be very difficult to remove from the skin in case of contact.
Step 4. Press the stand against the adhesive surface and let it sit for 8 hours
Press the adhesive part against the surface to which the stand is to be attached. Press firmly for 10-15 seconds. Allow the stand to adhere to the surface of the object for 8 hours before use to ensure it adheres firmly.
The popsocket holder can only be glued once. So, position carefully before installing
Tips
- If you're installing the popsocket on the back of a glass phone (like an iPhone 8, 8+, or X) make sure you get a plastic adhesive disc so the phone can stick. However, be careful that this disc can only be reinstalled three times.
- If the popsocket doesn't stick to the phone, push the popsocket and let it sit for at least 8 hours before opening.
