Even if you are a very clean person, your Playstation 4 game console will still be dusty which can cause overheating and damage. Using compressed air and a dry cloth to clean the exterior of the console can prevent this from happening. The fan inside the console may also need to be cleaned with compressed air occasionally if it gets louder. Compressed air and a dry cloth can also keep game console controllers clean, but sometimes you may need a damp cloth to clean the dirt off your Playstation 4.
Step
Method 1 of 3: Cleaning the Exterior
Step 1. Unplug all cables
First of all, first unplug the power cord from the console so that no electric power flows when cleaning. After that, remove the controller from the console. Do the same in the other section until you can access all console ports.
Step 2. Place the console on a clean surface
If you want to clean the console, you should also clean the console storage area. Move your Playstation 4 and place it in a clean, dust-free area. The process will be easier if you work in a clean area so that the console won't get dirty again when you clean it.
Step 3. Use compressed air properly
Before you start spraying compressed air on your expensive electronics, remember that there is liquid in the can. Hold the can of air upright to reduce the risk of the liquid inside escaping. In addition, keep the tip of the sprayer about 13 or 15 cm from the area to be cleaned because too close a distance will reduce its effectiveness.
Read the instructions on the compressed air package you are using for additional instructions for use or warnings
Step 4. Blow the dust on the console
Start spraying air into the groove in the center of the console. After that, clean the port area on the front and back of the console. Finally, clean the dust on the rest of the Playstation 4 surface, including the vents.
Step 5. Wipe the console with a dry microfiber cloth
Make sure you use a dry, clean cloth to remove stubborn dust as a wet cloth can damage your console. Wipe the entire exterior side to complete the cleaning process. When cleaning each side, repeatedly move your rag in one direction away from the light sensor to prevent dust from accumulating there. Don't brush the dust towards the port and mess up your work.
Step 6. Clean the console storage area, then place the device back
Move the console and clear the area you used to store it. Depending on the accumulated dust and the amount of dust flying, you may need to wait a while for the dust to clear before putting the console back in there. If so, put the console back in its original place.
Method 2 of 3: Cleaning the Fan on the Game Console
Step 1. Consider the warranty period of your game console
Since the fan is located inside the game console, you will need to open it for cleaning. Please understand that this will void the device warranty. Usually, the warranty is only valid for one year. However, a voided warranty can affect the selling price of the console if you want to sell it at a later date.
With that in mind, you may still need to clean the fans on the console. Cleaning needs to be done when the fan noise is louder than the sound when it was first used. Ideally, this problem should not appear until one year of use. If it happens faster, the fan inside the console must be cleaned even if the warranty is still on so as not to overheat (overheating)
Step 2. Remove the cables, screws, and the bottom half of the console cover
Unplug the console from its power source, then unplug any other cables so they don't get in your way. After that, look for the four screws on the back of the console. There are at least two screws covered by the warranty sticker so the sticker must be removed first. Remove the console screws with a T8 or T9 screwdriver, then carefully remove the bottom half.
Step 3. Clean the fan and other components with compressed air
Once the internal components have been exposed, spray compressed air carefully to prevent the liquid inside from escaping. Hold the can upright at least 13 to 15 cm from the console fan. The fan will most likely need to be cleaned. So, start with that part. If needed, you can:
Also spray compressed air on all areas that appear dusty, except for the hard drive. Spraying air directly can damage the hard drive
Step 4. Let the interior of the Playstation dry by itself
Do not risk damaging the device by wiping it like the exterior. Also, take the safest steps and assume that some liquid is coming out of the can of compressed air. Allow the game console for half an hour (or more, if necessary) to let it dry on its own, just in case.
Step 5. Install the game console as usual
Don't worry if there's still some dust left. Just install the console as before when you have cleaned most of the dirt that has stuck to it. As long as the device is allowed to dry on its own, you can safely reassemble it for normal use.
Method 3 of 3: Cleaning Game Console Controller
Step 1. Disconnect all cables from the console controller
Just like the console, you'll need to gain access to the charging port in order to clean it thoroughly. Unplug the charging cable. Do the same for the common speaker cables if each is attached to the console controller.
Step 2. Spray compressed air all over the console controller
Just like the console, you need to remove as much dust as possible with the compressed air. Focus on the gaps between the console's controller body and the buttons, pads, and analog sticks, as well as any gaps where dust might enter the interior. Make sure to spray the cable ports as well.
Step 3. Wipe the console controller housing with a dry microfiber cloth
Unlike consoles, most of the time the controllers are in your hands and need to be cleaned more thoroughly. Start by wiping it off with a dry microfiber cloth. Pay attention to the cleaning results before using a damp cloth.
Step 4. Replace with a damp washcloth if needed
If a dry cloth isn't enough to remove stubborn dirt, use a damp cloth or dampen the corner of a clean rag. First, remove as much of the liquid on the rag as possible so it doesn't drip all over the place. After that, when wiping the console controller, make sure to avoid the area near the charging port and speaker plugs to prevent water from getting inside. Finally, allow the console controller to dry completely before plugging it back in.
