3 Ways to Fix a Washing Machine that Stops Halfway

Table of contents:

3 Ways to Fix a Washing Machine that Stops Halfway
3 Ways to Fix a Washing Machine that Stops Halfway

Video: 3 Ways to Fix a Washing Machine that Stops Halfway

Video: 3 Ways to Fix a Washing Machine that Stops Halfway
Video: How to Paint a Brick House the RIGHT Way | DIY Painting 2024, November
Anonim

Washing machines are complex, but when they stop working midway, there are ways to fix the cause even if you don't have any special skills. If the cause is blackout, try doing a master reset. If you're having trouble with the water level, try testing the water control button. If the machine fills with water and rolls over, but does not turn, it is best to check the shut-off button.

Step

Method 1 of 3: Performing a Master Reset

Fix a Washing Machine That Stops Mid‐Cycle Step 1
Fix a Washing Machine That Stops Mid‐Cycle Step 1

Step 1. Unplug the washing machine power cord

Often problems with washing machines are caused by power surges or computer malfunctions. In this case, unplugging the washing machine is the first step in resetting the computer and fixing the problem.

This is usually the first thing to try as it is less invasive or burdensome to the machine than other methods

Fix a Washing Machine That Stops Mid‐Cycle Step 2
Fix a Washing Machine That Stops Mid‐Cycle Step 2

Step 2. Wait for one minute and reconnect the power cable

Do not directly plug the power cord into a wall outlet. Leave it unplugged for a minute.

Fix a Washing Machine That Stops Mid‐Cycle Step 3
Fix a Washing Machine That Stops Mid‐Cycle Step 3

Step 3. Open and close the machine door several times quickly

Try opening and closing the washing machine door within 12 seconds. Many washing machines are set up so that this step signals the computer to reset.

Fix a Washing Machine That Stops Mid‐Cycle Step 4
Fix a Washing Machine That Stops Mid‐Cycle Step 4

Step 4. Test the washing machine

To see if the washing machine is back properly, set it to “small load” and let it run without charging anything. When the washing machine completes its cycle, it means that the clothes can be washed again.

Method 2 of 3: Diagnosing Key Cover Malfunction

Fix a Washing Machine That Stops Mid‐Cycle Step 5
Fix a Washing Machine That Stops Mid‐Cycle Step 5

Step 1. Find the closing button

The shut-off button is part of the top lid washer, which sends a signal to indicate that the door is closed and that washing can begin. There should be a square hole that is straight with the rod on the inside of the door so that it fits snugly in.

Because it tends to wear out, this part is easily broken. As a result, this is one of the most common reasons why a washing machine stops midway

Fix a Washing Machine That Stops Mid‐Cycle Step 6
Fix a Washing Machine That Stops Mid‐Cycle Step 6

Step 2. Check the close button

Usually the condition of the closing button can be guessed by looking and touching. The button must be flush with the top panel. If it's loose, it looks like the button is broken.

You can also touch the close button to see if the spring on the back is working properly. If the close button does not want to be pressed or it bounces back to its original position, there seems to be a problem with the close button

Fix a Washing Machine That Stops Mid‐Cycle Step 7
Fix a Washing Machine That Stops Mid‐Cycle Step 7

Step 3. Release the cover button

The process of releasing this cap button depends on the washing machine model. Read the user manual to find out how to remove it, or enter the keyword “removing the washing machine cover button” into a Google search, along with the model number and serial number of the washing machine you own to find a solution. When releasing the cover button, leave the cable plugged in.

Be sure to disconnect the washing machine's power cord before removing any machine components

Fix a Washing Machine That Stops Mid‐Cycle Step 8
Fix a Washing Machine That Stops Mid‐Cycle Step 8

Step 4. Test the cover button with a multimeter

Put the multimeter in continuity mode (continuous). Find the connector on the cover button, remove it, and touch the multimeter on the two outer connectors on the button cover so that it touches the metal inside. Press the shut down button and perform the continuity test.

The multimeter should recognize continuity mode when you press the shut down button, which usually happens when the door is closed. If the button is not pressed, the multimeter does not recognize continuity

Fix a Washing Machine That Stops Mid‐Cycle Step 9
Fix a Washing Machine That Stops Mid‐Cycle Step 9

Step 5. Order a new close button

These buttons can be purchased via the internet, usually for IDR 150,000-300,000 per piece. Contact the washing machine manufacturer, and state the model number so they can find a cover button that fits your washing machine.

Fix a Washing Machine That Stops Mid‐Cycle Step 10
Fix a Washing Machine That Stops Mid‐Cycle Step 10

Step 6. Replace the cover button

You need to read the user manual to find out how to replace the cover button according to the washing machine model you have. However, if you've let go of the old shut down button, the next step shouldn't be too difficult. You just need to install the new button where the old button was, screw it in, and connect it to the electronic control board like the old shutter button.

Once the shutter button has been replaced, you will need to mount the console and reconnect the machine to the wall

Method 3 of 3: Fixing Water Level Control Malfunction

Fix a Washing Machine That Stops Mid‐Cycle Step 11
Fix a Washing Machine That Stops Mid‐Cycle Step 11

Step 1. Remove the control panel

The control panel is a multi-button interface that you use to operate the washing machine. Use a plus screwdriver to remove the screws that secure the control panel.

Fix a Washing Machine That Stops Mid‐Cycle Step 12
Fix a Washing Machine That Stops Mid‐Cycle Step 12

Step 2. Test the water level control valve

You can find the plastic hose under the control panel which is firmly connected. Remove the water level control valve and blow. Air should flow naturally. If you can't exhale naturally, it looks like there's a blockage that needs fixing.

If the hose is disconnected, it means that the hose needs to be reconnected to the pressure button so that the washing machine can work again

Fix a Washing Machine That Stops Mid‐Cycle Step 13
Fix a Washing Machine That Stops Mid‐Cycle Step 13

Step 3. Clean the water level control valve

If the hose seems clogged, fill the turkey baster with vinegar and pump it into the hose. The vinegar will dissolve the soap residue and return the washing machine to normal.

Fix a Washing Machine That Stops Mid‐Cycle Step 14
Fix a Washing Machine That Stops Mid‐Cycle Step 14

Step 4. Test the pressure button with a multimeter

The plastic hose should connect to the pressure switch, which measures the amount of water in the washer. This pressure button is a circle that looks like a gear and is connected to a hose. Usually this button is below the control panel. Disconnect the cable and connect it to the multimeter to check continuity.

  • The washing machine has three separate plugs, which also means there are three pairs of connections to test with a multimeter. Test each of these pairs separately. There should be connectivity between all pairs.
  • If the washer doesn't fill up or overflows, this is a sign that there is a problem with the pressure button or water level control valve.
Fix a Washing Machine That Stops Mid‐Cycle Step 15
Fix a Washing Machine That Stops Mid‐Cycle Step 15

Step 5. Replace the pushbutton as per specifications

Every washing machine make and model has its own unique method of replacing the pushbutton. If the test results confirm that the problem is with the pushbutton, consult the user manual to find out how to replace it.

Recommended: